Käyttöohje SILVA PULSE

[. . . ] 9 2. 1 Tietokoneen asetukset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 2 Laitteen käyttöönotto. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 2. 1 ETHERNET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 2. 2 Langaton lähiverkko (WLAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your router (e. g. telephones, fax machines, analog modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and to ensure that all line filters are correctly installed and the right way around. Missing line filters or line filters installed being the wrong way around can cause problems with your ADSL connection, which includes frequent disconnections. 14 Chapter 3 Installation You can configure the PULSE v3 (b) router through the convenient and user-friendly interface of a web browser. Most popular operating systems such as Linux and Windows 98/NT/2000/XP/Me include a web browser as a standard application. 3. 1 Before Configuration PCs must have a properly installed Ethernet interface which connects to the router directly or through an external repeater hub. In addition, PCs must have TCP/IP installed and configured to obtain an IP address through a DHCP server or a fixed IP address that must be in the same subnet as the router. The default IP address of the router is 192. 168. 0. 254 and the subnet mask is 255. 255. 255. 0 (i. e. any attached PC must be in the same subnet, and have an IP address in the range between 192. 168. 0. 1 and 192. 168. 0. 253). The easiest way is to configure the PC is to obtain an IP address automatically from the router using DHCP. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK. 19 3. 2 Factory Default Settings Before configuring the PULSE v3 (b) router, you need to know the following default settings. Web Interface: (Username and Password) Username: admin Password: admin The default username and password are "admin" and "admin" respectively. LAN Device IP Settings: IP Address: 192. 168. 0. 254 Subnet Mask: 255. 255. 255. 0 ISP setting in WAN site: RFC 1483 LLC Bridge Auto support for VPI = 0, 14 and VCI = 24, 33, 50, 100 if auto-scan fails DHCP Server and NAT: DHCP server and NAT is enabled in ports 1 and 2, ports 3 and 4 are in bridged mode Start IP Address: 192. 168. 0. 100 IP pool counts: 100 20 3. 3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are preset at the factory. LAN Port IP address Subnet Mask DHCP server function IP addresses for distribution to PCs 192. 168. 0. 254 255. 255. 255. 0 Enabled in ports 1 and 2 100 IP addresses continuing from 192. 168. 0. 100 through 192. 168. 0. 199 WAN Port The RFC1483 Bridged IP LLC function is enabled to automatically get the WAN IP address from the ISP 3. 4 Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of services are provided, such as PPPoE, PPPoA, MPoA or Pure Bridge. Gather the information as illustrated in the following table and keep it for reference. PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, Service Name, and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually). PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually). RFC1483 Bridged RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode. VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask, Gateway address, and Domain Name System (DNS) IP address (it is fixed IP address). 21 3. 5 Configuring with your PULSE v3 (b) 1. To configure this device, you must have IE 5. 0 / Netscape 4. 5 or above installed 2. [. . . ] SNMPv3 is a strong authentication mechanism, authorization with fine granularity for remote monitoring. Traps supported: Cold Start, Authentication Failure. The following MIBs are supported: From RFC 1213 (MIB-II): 91 System group Interfaces group Address Translation group IP group ICMP group TCP group UDP group EGP (not applicable) Transmission SNMP group From RFC1650 (EtherLike-MIB): dot3Stats From RFC 1493 (Bridge MIB): dot1dBase group dot1dTp group dot1dStp group (if configured as spanning tree) From RFC 1471 (PPP/LCP MIB): pppLink group pppLqr group From RFC 1472 (PPP/Security MIB): PPP Security Group) From RFC 1473 (PPP/IP MIB): PPP IP Group From RFC 1474 (PPP/Bridge MIB): PPP Bridge Group From RFC1573 (IfMIB): ifMIBObjects Group From RFC1695 (atmMIB): atmMIBObjects From RFC 1907 (SNMPv2): only snmpSetSerialNo OID 92 5. 3. 8. 7 Remote Access Remote Access Control: Enable: Select Enable to allow management access from remote side (mostly from internet). Duration: Set how many minutes to allow management access from remote side. [. . . ]